Glossary Of Technical Terms
Natsyn, Cariflex IR
Buna Huls, Polysar S, Solprene
Buna CB, Polybutadien K
Polysar Butyl, Esso-Butyl
Keltan, Buna AP, Dutral
Perbunan, Polysar, Krynac
Viton, Flourel, Tecnoflon
Hydrous acrylonitrile-butadiene rubber
A ring used to support a softer sealing ring and prevent it from extruding.
Anti-extrusion ring or support ring.
See Wear Ring
A seal that prevents leakage from both directions.
Continued deformation under stress
Materials made from two or more constituent materials with significantly different physical or chemical properties which remain separate and distinct on a macroscopic level within the finished structure.
The permanent deformation of a seal after release of a compressive load.
A copolymer is a polymer derived from two (or more) monomeric species.
Creep is the tendency of a solid material to slowly move or deform permanently under the influence of stresses.
Double acting Seal
A seal designed to take pressure from two sides.
A seal designed to prevent leakage between two moving surfaces.
The property of a substance that enables it to change its length, volume, or shape in direct response to a force effecting such a change and to recover its original form upon the removal of the force.
An elastic substance occurring naturally, as natural rubber, or produced synthetically, as butyl rubber or nitrile.
Distortion or flow of part of a seal into an extrusion gap under pressure.
The clearance on the low pressure side between two parts, which house the seal.
A seal that is compressed in a direction parallel to its axis.
Extruded material on the partially finished product formed during the molding process.
A surface cracking induced by repeated bending or flexing.
The height of a seal in its free-state.
Friction is the force resisting the relative motion of two surfaces in contact.
A rubber, metal, or other material, for packing a piston or placing around a joint to make it seal a fluid or gas.
A cavity into which a seal is installed. Component at the working end of a cylinder which contains seals.
The measured resistance of a material to indention, abrasion, deformation, or machining.
A rigid component which contains a seal assembly.
A hydraulic seal is usually a relatively soft, non-metallic ring captured in a groove or fixed in a combination of rings, forming a seal assembly, to block or separate fluid in reciprocating motion applications.
The rate at which a fluid passes a seal in a given time.
An elastomeric seal that prevents leakage in rotary seal applications through the use of one or more contact lips operating on the shaft surface. These seals are commonly called shaft seals, oil seals or rotary lip seals.
A toroidal shaped sealing device usually made from an elastomeric material, may also be made from metal or PTFE.
An elastomer with high temperature and chemical resistances.
Permanent deformation of spring or elastomer upon release of load.
The passage of a fluid under pressure through a solid material by diffusion.
A material formed by the joining together of many (poly) units (mer) of one or more monomers.
Quality or state of being porous.
A seal used to keep dirt or other foreign matter out of a hydraulic or pneumatic device.
A device designed to prevent the passage of a medium (fluid or solid).
Single acting Seal
A seal designed to take pressure from only one side.
A machine element capable of restoring energy and releasing it.
A seal between two non moving parts.
Ratio of the maximum load a material can support without fracture when being stretched to the original area of a cross section of the material.
Expansion caused by increase in temperature.
A seal that prevents leakage from only one direction.
An enclosed space that is occupied by a gas at less than atmospheric pressure.
Refers to a specific curing process of rubber involving high heat and the addition of sulfur or other equivalent curatives.
A minute amount of liquid passing by a seal.
Element used to protect moving parts from wear.
* NOTE: Any special and non-standard O-Rings and Flat Gaskets can be moulded with NO tooling charge. Especially big sizes and non-standard sizes.